Cement Testing Equipment

Product Details:

The proving ring is a device used to measure force It consists of an elastic ring of known diameter with a measuring device located in the center of the ring Proving rings come in a variety of sizes They are made of a steel alloy Availbale from 100kN upto 2000kN

Product Details:

IS 4031 2645 2542 PART 1 1727 5513 amp 712 BS 12 146 915 1370 4027 4246 4248 AASHTO T 129 E 131 Consists of a metallic frame bearing a movable rod with cap at one end and a vicat mould 70mm in dia at the base 50mm at the top and 40 mm high and with a glass base plate consistancy plunger intial and final needless in a nice Jewellery case

Product Details:

ASTM C 266 This is used for determining setting time of hydraulic cement It consists of a base with a vertical shaft and two horizontal arms the lower arm being adjustable for height Supplied complete with one initial needle one final needle and a glass base plate

Product Details:

As per IS 5512 for cement Mortar and Lime The flow table consists of a brass table top 250 2 5mm dia mounted on a rigid stand The table top is reinforced with equally disposed ribs and allowed to drop through 12mm by a ground and hardened cam Complete with mould 100mm base dia 70mm top dia and 50mm high The cam shaft is rotated at the rate of 100 RPM by an electric motor Suitable for operation on 230 Volts 50 cycles

Product Details:

IS 1199 Electrically operated to raise and drop the table top approx 15 times in 15 seconds Suitable for operation on 230 volts 50 cycles A C Supply Flow Table

Product Details:

Brass tube approximately 53 cm long and 2 8 cm I D with a wooden handle Total length approximately 73cm.  The tube has the sharp angular edge which conveniently pierces cement bags.  An air hole of approximately 3mm dia is drilled on the tube near handle.  Total sample collected at one time is 300 cm approximately

Product Details:

IS 4031 5516 1727 and 4828 ASTM C 204 BS 4359 2 The Blaine Air Permeability Apparatus determines the fineness of Portland cement in terms of specific surface The Humboldt Blaine Air Permeability Apparatus consists of calibrated U tube manometer ground glass joint stainless steel test cell and plunger rubber aspirator bulb and perforated disc Includes an 8 oz 226 8g bottle of red manometer fluid filter paper wood block for holding test cell during filling and a funnel

Product Details:

Slump Cone Specifications as per IS 7320:1974

1. Material: Mild steel or non-corroding metal
2. Height: 300 mm
3. Bottom Diameter: 200 mm
4. Top Diameter: 100 mm
5. Wall Thickness: Minimum 1.6 mm
6. Handles: Two handles for lifting
7. Footpieces: Foot flanges with clamps for securing the cone
8. Tamping Rod: 16 mm diameter, 600 mm length, rounded at one end

Product Details:

IS 4031 1727 Cement Mortar Mixer is used for mixing cement pastes mortar and pozzolanas The mixer consists of an epicycles type stainless steel paddle imparting both planetary and revolving motion and it has two speeds

Product Details:

IS 11262 1985 ASTM C 186 Heat of Hydration apparatus is used for determining heat of hydration of cements by measuring difference between heat of solution of dry cement and heat of solution of a separate sample partially hydrated for 7 days amp 28 days

Product Details:

Description Standard Magnetic Stirrer with Hot Plate are electronic devices use to uniformly heat the liquid with or without stirring it Technical Specification A stir bar is immersed into the liquid and the device generates a magnetic field Because it causes the bar to rotate and thereby generating a vortex stirring the liquid Similarly we can easily adjust The temperature of the hot plate and the frequency of rotation rpm manually MDC motor for higher torque even at low speeds It is equipped with a hot plate that is made by using the finest grades of stainless steel alloys and is powered by reliable PMDC motor for remarkable torque at a lower speed It achieves superior stirring even with small volumes of different viscosities It can also achieve seamless variation up to 1200 RPM with the precise speed control mechanism We maintain stringent standards of quality by adhering to set standards of the domain Accessories Extra PMDC motor for higher torque even at low speeds Better speed regulation even with small volume amp low speed Accurate stepless speed control maintains excellent speed stability Digital speed indicator for display of stirring speed totally enclosed unit Designed for use even in a corrosive atmosphere

Product Details:

Description Standard The Cement Autoclave Apparatus used to determine soundness of cement by autoclave method Our Laboratory Cement Autoclave comprises of stainless steel Vessel with lead having thermocouple well tighten on vessel with nut amp Bolts and the high pressure vessel hydraulically tested cylinder and is equipped with a welded metal that is heat insulted with attractive finish Technical Specification Laboratory Cement Autoclave equipment comes with a spring loaded safety valve and pressure gauge and PID controller along with RTO used for controlling the heater unit We provide accelerated curing of mortar bar specimens in controlled steam pressure and temperature to determine the expansion of hydraulic cements by the ASTM method and control unit surrounds a pressure gauge and sensitive pressure regulator